A Step-by-Step Overview to Installing a Bath Tub
A Step-by-Step Overview to Installing a Bath Tub
Blog Article
We have noticed this great article relating to A Step-by-Step Guide to Installing a Bathtub down the page on the net and reckoned it made perfect sense to relate it with you on my blog.
![A Step-by-Step Guide to Installing a Bathtub](https://www.thespruce.com/thmb/4p35UP1exwe92DJt_i1fjaTl0Ks=/1500x0/filters:no_upscale():max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Installing a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old tub with a new one is likewise a moderately hard project. If the old bathtub is readily obtainable, the project can relocate quickly; if you need to open up a wall to get rid of the old tub as well as position the brand-new bathtub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will require a helper to vacate the old tub as well as set in the new one. See to it you have certified yourself for the task and also are comfortable trying it. Rather than employing a contractor to take over a halfway-completed task, it is better to think about employing one before you start. Chances are you may require a professional plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your shower room if you have actually already purchased a brand-new bathtub and don't require to change the plan of your previous water system pipelines.
Your tools as well as product list should make up the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The process of removing the existing taps can be rather bothersome as a result of the limited access that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will come from the pipes. Once the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to proceeding to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making certain that the washing machines are in place in between the faucet as well as the sink. Protect the tap in place with the supplier supplied backnut. When the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous kind ought to be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Using both wood boards under its feet, put the bathtub in the required placement. The wood boards are useful in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and adjusting the feet on the bath tub up until the spirit level reviews level.
To install faucets, fit the bottom of the furthest adaptable faucet connector to the ideal supply pipe by making a compression join; after that do the exact same for the other faucet.
Turn on the water supply and also check all joints and also brand-new pipework for leaks and also tighten them if required. Fill the bath tub and likewise check the overflow electrical outlet and the typical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the supplier's instruction manual. Tiling and also sealing around the tub needs to wait up until the bath tub has been utilized at least once as this will certainly settle it right into its last position.
Planning for the Installation
First of all, the sustaining frame supplied with the bath must be fitted (if required) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to avoid pressure on the bathtub.
Fit the flexible tap adapters to the bottom of both taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last position.
Tiling Around the Bathtub
In the location where the bath meets the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bath and the tiling, leading to complications with dampness and feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes and also cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the tub with water before securing, to enable the motion experienced when the bathtub is in use. The sealant can break fairly early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently offered on the market. It is recommended to fit the tiles using waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
![Installing A Bathtub](https://a.mktgcdn.com/p/_b6ag6E13cLQuNZ6zHh3CZy7JG_5MTx4f9v0Px1dZAc/800x600.jpg)
I'm just very intrigued by Tools You Need to Install a New Bathtub and I'm hoping you enjoyed reading my page. In case you enjoyed reading our page please remember to share it. We recognize the value of reading our article about Installing A Bathtub.
Appointment
Report this page